Turn Signal Relocation Kit

Part Number 68732-02A




Kit moves turn signals from rear fender struts to a license bracket mounted turn signal bar.

  • Required for installation of Saddlebags on Dyna® models

Required to install Saddlebags P/N 91615-09A, 88200-09A, 90181-08A, 90460-06B, 79300-06A, 90564-06B, 90369-06C, and 88343-10. Fits '02-'17 Dyna® (except FXDF, FXDWG and '09-'17 FXDB) and '04-later XL models (except XL883N, XL1200N, XL1200NS, XL1200X, XL1200XS and '11-later XL1200C). Does not fit with Layback License Plate Mounting Kits.

Bike not listed?
Select your year and model to see all the parts that fit your bike.

  • Model
  • Position on Bike

  • Warranty

    1 year limited warranty – Go to for full details
  • Sold in Unit

  • In The Box

    Relocation hardware
Turn Signal Relocation Kit is rated 3.8 out of 5 by 4.
Rated 3 out of 5 by from Fit my CVO Dyna but... Not a very pretty kit. It did away with my awesome chrome license plate holder for a cheap black steel one. So I modified my original plate holder and used the hardware and bar from the kit to make my own. Now it looks good! I don't know why Harley doesn't mount the turn signals back there in the first place.
Date published: 2017-07-11
Rated 2 out of 5 by from A must Not sure what to say, there is nothing spectacular about turn light relocation. I'd recommend some engineering that would position the lights in a better position so the relocation isn't necessary to begin with
Date published: 2014-05-10
Rated 5 out of 5 by from Works on a Fatboy I was looking for a way to mount aftermarket saddlebags to my Fatboy, but even with the signals mounted to the rear fender bracket hole I still wasn't getting enough room for the bags I had. After consulting with my local dealer, we found this kit. It bolts right up to my softail, and rather than using all 3 bolt holes I left the top one empty to run the wires through. The bottom 2 are integrated into the new signal bar, and you really only NEED those 2 to mount the license plate bracket. Worked great. Now I have "full size" bags on my Fatboy and everything clears correctly and also looks great at the same time. Highly recommended for those in the same position!
Date published: 2014-04-18
Rated 5 out of 5 by from Super product, easy to install This was very easy to install. I found it better to drill the hole on the right side of the rear fender and run the wiring up that side as there is no other wiring on this side. The connectors are difficult without the correct tool, but not impossible. Used this to move the signal lights so I could mount leather saddle bags I bought elsewhere. Looks like it came this way from the factory. Two thumbs up.
Date published: 2013-10-14
  • y_2018, m_2, d_26, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_4
  • loc_en_US, sid_PA-11-6873202A, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

Will this kit hide the wiring so it is not visible?

Where are the wires run through?
Asked by: Philk85


I have this kit but it will not work with my 2011 Superglide, unless I buy a different set of lights for the rear turn signals. The stock ones will not fit this relocation kit. I am a little disappointed since I spent a good bit on the bags and kit and now I have to go buy another set of lights. I wish this was addressed in the information provided.
Asked by: Smoguy

are these identical kits?

Online there are two kits listed, 68732 and 68733. Both say the fit a XL1200 custom. What is the difference in the two kits?
Asked by: Schwoby
Hi Schwoby, Thank you for your question. The difference is that this one is meant for Domestic bikes and the other part number, 68733-02A, is meant for international bikes. The only difference is the turn signal bar. The signal bar on the international kit is longer to meet international requirements. Hope this helps!
Answered by: PeteHD
Date published: 2016-04-23

Can I use it with LED Bullet Turn Signal Kit-67800055?

Hello! I'd like to change stock rear turn signals to LED Bullet Turn Signal Kit. Now I use Layback License Plate Kit P/N 60215-06. I cannot to install LED signals because the kit doesn't fit it. So my question is: does this turn signal relocation kit fit to led signals?
Asked by: IceBull
If you could provide the year and model of your motorcycle we could try and provide some additional info. Thanks!
Answered by: HDJuneauAve
Date published: 2014-11-29

Are all the parts chrome?

Two of the pictures show the license plate and the bracket that mounts to the fender as black, but the picture of the kit mounted on a motorcycle shows the plate and the bracket as chrome. Which is it?
Asked by: jrduncan59
Hey jrduncan59, The license plate holder is black. We've updated the photo...apologies for the confusion!
Answered by: Wisco832
Date published: 2014-03-04
  • y_2018, m_2, d_26, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_6
  • loc_en_US, sid_PA-11-6873202A, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

Recently Viewed

    Please Hold Your Iron Horses

    You've been sitting idle, so we've ended your session to protect your personal details.

    Continue as guest Sign in
    Online Exclusives

    You’ve been sitting idle, so your session will expire in

    Would you like to remain signed in and continue shopping?

    Yes, keep me signed in No, sign me out

    Prices listed are generally the Manufacturer's Suggested Retail Price (MSRP), excluding taxes and shipping. Prices at local dealerships may vary. All online orders will be fulfilled and shipped by
    Harley-Davidson Motor Company as the agent for the Selling Dealer.