FREE SHIPPING WITH $50 PURCHASE AND FREE RETURNS - LEARN MORE

Trunk Guard

Part Number 83825-09B

FINAL SALE, NON-RETURNABLE

Finish / Color: Chrome

Quantity:

A A A

Unique rear guard wraps around the bodywork to protect your finish from damage. Lightweight steel tubing incorporates high-quality welded joints and is hand-polished and chrome-plated for a brilliant finish.

  • Lightweight steel tubing incorporates high-quality welded joints
  • Hand-polished and chrome-plated for a brilliant finish
  • Includes all necessary mounting hardware for bolt-on installation
A A A

Bike not listed?
Select your year and model to see all the parts that fit your bike.

  • SELECT
  • Model
Shop
  • Warranty

    1 year limited warranty – Go to www.h-d.com/warranty for full details
  • Sold in Unit

    Each
  • In The Box

    Rear guard and all necessary mounting hardware for bolt-on installation
Trunk Guard is rated 4.8 out of 5 by 24.
Rated 4 out of 5 by from Impedes the opening of the trunk Really is a nice looking, well made product. My only complaint is that I can no longer fully open the truck, which makes it really hard to store 2 helmets in it, or get a small suitcase in it. Back to duffle bags! I would have given 5 stars if not for the opening issue.
Date published: 2017-11-28
Rated 5 out of 5 by from It looks good. It looks good but may not actually protect the trunk from a short curb.
Date published: 2017-11-01
Rated 5 out of 5 by from More Chrome Had this installed on the trike before delivery so I can't comment on installation. Don't know if it'll hold up in a collision but it looks great and should protect against the accidental scrape or bump in the garage.
Date published: 2017-09-18
Rated 5 out of 5 by from Appealing and necessary Many times our bikes and trikes are too complicated for the average person to wrench on, but this one is an exception. I decided that I needed a bumper (trunk guard, as Harley calls it), and wanted to install it myself. I looked at the aftermarket prices and read some of the reviews, where I saw fitment issues and missing hardware, so I drove to my local Harley shop and bought one over the counter. Yeah ... it cost me a few more bucks, but it usually eliminates a lot of later hassles with having to send something back, or make it fit. As it turned out, it was a simple install with only four bolts. Hint - install them one at a time and not all at the same time. I used some extra fender washers, just in case, and the installation went well. It was a solo project, but within half an hour, I was done.
Date published: 2017-07-19
  • y_2018, m_2, d_26, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_24
  • loc_en_US, sid_PA-04-8382509, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

what is the diameter of the 83825-09 trunk guard

I require the diameter for the trunk guard bar p/n 83825-09
Asked by: k9wolf
Hey k9wolf, Diameter of the actual bumper tube is 1.50".
Answered by: Rockstar883
Date published: 2016-03-24

do you have a copy of the installation that you can email myself?

I bought the bumper from an owner that didn't put on his trike but no info instructions
Asked by: Isidro
Hey Isidro, I've emailed the I Sheet to you and included the part numbers for the service parts, too.
Answered by: Rockstar883
Date published: 2015-07-09

What is the part numbers for the nuts & washers

Asked by: Isidro
Hi Isidro, The screws, nuts, and washers are as follows: Hex head cap screw, 5/16-18 x 3.25 in (4): P/N 10500002 Hex locknut, 5/16-18, with nylon insert (4): P/N 7739 Plain washer (4): P/N 6645 Thank you for your question.
Answered by: FXS78
Date published: 2015-07-17

What is the part number for the bolts? I need to replace mine.

Asked by: lmayle
Hey lmayle, Thank you for your question. The part number for the bolt is 10500002. Thank you!
Answered by: PeteHD
Date published: 2014-09-23

Will the rear guard extend out beyond my new screaming eagle mufflers?

I've change my original stock mufflers to the new screaming eagle street canons. The add on style muffler tips stick out further than the original muffler. Would prefer the guard to stick out far enough to protect muffler as well as trunk. Maybe you guys can make slotted mounting brackets to accommodate the performance mufflers.
Asked by: Rickyacky
As I told Karl above, the bumper extends 2 1/4" beyond the rear body panel. I don't know if that's enough to protect the ends of your Screamin' Eagle pipes or not - you'd have to measure where your pipes are from the rear body panel to see. The stock pipes extend about 1 3/4" it looks like, maybe just a little more, so the bumper just covers them.
Answered by: DrDave1620
Date published: 2018-02-21
  • y_2018, m_2, d_26, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_6
  • loc_en_US, sid_PA-04-8382509, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

Recently Viewed

    loading
    Loading...
    Please Hold Your Iron Horses

    You've been sitting idle, so we've ended your session to protect your personal details.


    Continue as guest Sign in
    Online Exclusives

    You’ve been sitting idle, so your session will expire in


    Would you like to remain signed in and continue shopping?


    Yes, keep me signed in No, sign me out

    Prices listed are generally the Manufacturer's Suggested Retail Price (MSRP), excluding taxes and shipping. Prices at local dealerships may vary. All online orders will be fulfilled and shipped by
    Harley-Davidson Motor Company as the agent for the Selling Dealer.