Long Angled Adjustable Highway Peg Mount Kit

Part Number 50829-07A


Finish / Color: Chrome



Stretch out for added comfort. This chrome-plated Adjustable Highway Peg Mounting Kit can be set for shorter riders, and it can be reversed to reach far forward for those with long legs.

  • 5" angled peg mounting kit in chrome finish
  • Angled design allows the arm to reach back and around to clear fairing lowers
  • Arm can be raised and lowered for a custom fit
  • Mounting clamp firmly grips the engine guard, and the locking design secures the peg at the desired angle
  • Includes chrome-plated mounting hardware
  • Footpegs sold separately

Fits 1.25" engine guards. Does not fit with Chopped Engine Guards.

Bike not listed?
Select your year and model to see all the parts that fit your bike.

  • Model


Do not use highway pegs under normal stop and go operating conditions. Doing so could result in death or serious injury.

  • Adjustable

  • Warranty

    1 year limited warranty – Go to for full details
  • Sold in Unit

  • In The Box

    Left and right side mounts and arms
  • Sold Separately

Long Angled Adjustable Highway Peg Mount Kit is rated 4.9 out of 5 by 22.
Rated 5 out of 5 by from Fits Great Less fit great and look good on my Street Glide and my Ultra Limited Low. Great to stretch out on the open road and makes a great place to hang my helmet at my stops.
Date published: 2018-01-08
Rated 5 out of 5 by from Feet can escape engine heat. These allow you to get your feet away from the hot M8 engine on a Tri-Glide. Moderate skills to install. A torque wrench is highly recommended. There is a strange torque requirement.
Date published: 2017-11-01
Rated 5 out of 5 by from Great fit on my TriGlide After wasting money trying to kluge together aftermarket pegs I went with a sure bet. Only took minutes to install and they look great.
Date published: 2017-07-11
Rated 4 out of 5 by from Finicky Fit. Limited adjust-ability, Overly tight fit on crash guard Installed on 2104 TriGlide. The purpose is to bring the highway pegs closer for short legged individuals like me. It does that job, however there really only is one position on the crash guard that it can fit, and one angle back that you can put this so that when the highway pegs fold up that they don't hit the side of the lower fairing and rub against the paint. So it does the job bringing pegs closer but took forever to find the height and angle to protect the fairing. Also, it is almost like the diameter of the clamp where they fit around the crash guard is too small. Again, one place narrow enough to place them and even then the clamp doesn't close enough to allow the plastic gasket to do anything but rattle. Finicky fit.
Date published: 2017-07-03
  • y_2018, m_2, d_26, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_22
  • loc_en_US, sid_PA-07-5082907, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

Can i purchase a bolf that came out of the rear near the foot peg. I have the foot peg and the spacer.

Just the rear bolt.
Asked by: Pdaddy
If you have kit number 50829-07 A or 50830-07 A, then you may be looking for item number 7, part number 4087A, Screw, 3/8 x 1 inch. You should verify this by reviewing the Service Parts section of the Angled Highway Peg Mounting Kits Instructions J02837.
Answered by: FootSkull13
Date published: 2018-02-20

Will these pegs fit a factory stock 2017 Tri Glide? Do I need to add an engine guard?

Asked by: luckydragon13
This highway peg mount kit fits fine on the stock 2017 Tri Glide engine guard.
Answered by: legs290
Date published: 2017-11-25

For the long angled adjustable highway peg mount kit, what size and thread type are the screwed stud adjusters?

Asked by: IndyRoadDog

Is this supposed to fit 2017 Ultra Limited?

It seems like the crash bar is larger than clamp needs and . Why cant I get the mini footboards to work at the correct angle?
Asked by: jeffreyisreal
Hi Jeffreyisreal, Yes, the Long Angled Adjustable Highway Peg Mount Kit is a direct validation for the 2017 Ultra Limited. If you having problems with the mini footboards, I recommend going to your local dealer for assistance. Also, do you have the correct minis for your bike--not for a FLHTKL (this is common)? Thanks!
Answered by: RowdyGrl79
Date published: 2017-01-03

Replacement Pieces

Why is Screw, 1/2 x 1-1/4 inch (2) Not sold separately? Some parts I can understand, but this is a screw that is easily damaged if the Allen key slips and is visible on the bike.
Asked by: Philip
It basically depends on the supplier of the kit, we apologize for the hassle. You may want to see if your local dealer is able to find this screw for you.
Answered by: Rockstar883
Date published: 2015-09-21
  • y_2018, m_2, d_26, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_8
  • loc_en_US, sid_PA-07-5082907, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

Recently Viewed

    Please Hold Your Iron Horses

    You've been sitting idle, so we've ended your session to protect your personal details.

    Continue as guest Sign in
    Online Exclusives

    You’ve been sitting idle, so your session will expire in

    Would you like to remain signed in and continue shopping?

    Yes, keep me signed in No, sign me out

    Prices listed are generally the Manufacturer's Suggested Retail Price (MSRP), excluding taxes and shipping. Prices at local dealerships may vary. All online orders will be fulfilled and shipped by
    Harley-Davidson Motor Company as the agent for the Selling Dealer.