Docking Hardware for H-D Detachables Windshields

Part Number 58350-96

FINAL SALE, NON-RETURNABLE

Finish / Color: Chrome

Quantity:

A A A

Kit includes detachable docking points and mounting hardware.

  • For 41mm forks
A A A

Required for installation of H-D® Detachables™ Windshields on '93-'05 FXDWG, '80-'86 FXWG and '84-'15 FXST, FXSTB and FXSTC models.

Bike not listed?
Select your year and model to see all the parts that fit your bike.

  • SELECT
  • Model
Shop
  • Warranty

    1 year limited warranty – Go to www.h-d.com/warranty for full details
  • Sold in Unit

    Each
  • In The Box

    Detachable docking points and mounting hardware

i need instructions to install a windshield on a 2008 night train

pictures can also be very helpful.
Asked by: gravy1
6. On FXSTB models only: Remove existing turn signal clamps from fork tubes. Remove the original turn signal standoff from the turn signal. The original clamp and standoff will not be used during re-assembly. 7. See Figure 5. Assemble mounting hardware for lower windshield mounting as shown in illustration. Assemble in the following order, and leave assembly loose: a. Locate the mounting hardware supplied in the docking hardware kit. Thread jam nut (9) from mounting kit onto the turn signal standoff end that is opposite the end with the flats (3). b. Thread standoff into turn signal assembly with jam nut facing turn signal. c. Place flat washer (5) and bushing (4) on standoff. d. Thread the clamp (8) onto the standoff. e. Install clamp assembly onto the fork tube with the clamp nut forward toward the headlamp. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 8. See Figure 6. Assemble hardware for upper windshield mounting as shown in illustration and tighten button head screws to 15 ft-lbs (20 Nm). The spacer (1), not visible in the illustration, fits between the retainer wire bracket (6, 7) and the upper fork triple clamp. is01988 Figure 3. 5/32 inch Minimum Clearance between Fuel Tank and Upper Bushing (looking down on docking point from above) NOTE Check for proper clearance between upper bushing and fuel tank before installing windshield as follows: See Figure 3. Turn the front forks to the left, allowing the fork to rest against the fork stop. Measure the clearance between the fuel tank and the upper bushing.We recommend using the shank end of the proper size drill bit as a feeler gauge between the fuel tank and the upper bushing. Before checking the clearance, place a piece of paper against the fuel tank to eliminate the possibility of scratching the fuel tank paint. Repeat this process with the front forks rotated fully to the right fork stop. If clearance is less than 5/32 inch (4 mm), contact your Harley-Davidson Dealer for additional information (reference P&A Service Bulletin P-40). 9. Hook the two top windshield assembly "jaws" into the grooves of the top bushings (4) then slide the lower clamp assemblies up until the lower bushings firmly fit into the lower windshield "jaws". 10. With windshield in place, tighten lower clamp (8) hardware by first tightening clamp nut to 10 ft-lbs (14 Nm). Be sure the clamp does not rotate during tightening (the mounting bushing must be parallel to the windshield brackets). 11. With clamps secured to forks, tighten standoff into mounting clamp to 15 ft-lbs (20 Nm). Then, align turn signals and tighten jam nuts (9) to 10 ft-lbs (14 Nm). - 12. See Figure 4. Remove windshield by grabbing windshield edges parallel with center brace and firmly pulling windshield loose from upper bushing grooves. Lift windshield assembly off of lower bushings. With windshield removed, and using cable straps in kit, securely route turn signal wires. After wires are secured, check turn signal wire clearance with the windshield installed. 13. Reattach brake line clamp to upper fork triple clamp. Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a) NOTE Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in death or serious injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. NOTE Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components.
Answered by: RockyXL883
Date published: 2013-10-23
  • y_2018, m_2, d_26, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_US, sid_PA-20-5835096, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_harleydavidson

Recently Viewed

    loading
    Loading...
    Please Hold Your Iron Horses

    You've been sitting idle, so we've ended your session to protect your personal details.


    Continue as guest Sign in

    You’ve been sitting idle, so your session will expire in


    Would you like to remain signed in and continue shopping?


    Yes, keep me signed in No, sign me out

    Prices listed are generally the Manufacturer's Suggested Retail Price (MSRP), excluding taxes and shipping. Prices at local dealerships may vary. All online orders will be fulfilled and shipped by
    Harley-Davidson Motor Company as the agent for the Selling Dealer.