Free Shipping and Returns to your local dealer Details

Satin Black Batwing Mini-Ape Handlebar-57485-11

Part Number 57485-11

Finish / Color:  Satin Black

Quantity:

In Stock Online

A A A

Throw your fists in the air with these 12" ape hangers. Shaped to rest your hands just above the top of the classic Bat Wing fairing, these bars feature a tall stance and minimal amount of pull back that help to achieve a cool yet comfortable riding profile.

  • Satin black finish
  • Accept internal wiring for a clean look
  • See More Info tab for additional components required for installation
A A A

Fits '09-later Electra Glide®, Street Glide®, Ultra Limited™ (except '10-'13 FLHTK) and Trike (except FLRT) models. Does not fit CVO™ models. All models require separate purchase of additional components for installation. '09-'13 FLHX and models with fairing-mount mirrors require separate purchase of handlebar-mounted mirrors and Fairing Plugs. Not for use with heated hand grips.

Bike not listed?
Select your year and model to see all the parts that fit your bike.

Shop
A A A

Note

Installation of some handlebars and risers may require a change in clutch and/or throttle cable and brake lines for some models. Handlebar height is regulated in many states. Check state or local laws before installation.

  • Collection
    Hard Candy Custom
  • Material Content
    Steel
  • Material Diameter
    1.0 Inch
  • Tip-to-Tip
    35.0 Inch
  • Base Width
    16.0 Inch
  • Knurl Center-to-Center
    3.50 Inch
  • Rise
    12.0 Inch
  • Pullback
    1.75 Inch
  • Warranty
    1 year limited warranty - See Customer Service section for details
  • Sold in Unit
    Each
  • In The Box
    Handlebar and bushings
  • Sold Separately
    Additional installation components
Rated 3 out of 5 by 4 reviewers.
Rated 3 out of 5 by Good height but paint and bar thickness could be better At 6'0 with a long torso, I was constantly reaching down for the stock bars and was not comfortable. These are a great height for me, my hands are just below my shoulders and the grips are right at the top of the fairing, not above. I bought aftermarket, smaller mirrors and drilled new holes lower on the fairing and look under my arms to see behind me. I prefer this cleaner look from the front and can still see behind. As for the install, you do not need cable or wire extensions. I disconnected all the wires from the cannon plug connectors, ran them through the bars and then re-routed the connectors that run to them in the fairing. Clutch and brake lines are plenty long. As for the bars, the black is painted not powder coated. So the paint chips and peels way too easy! Especially when you are trying to position the hand controls. These bars pick up a little more vibration but are not that bad. I.M.O. they need to be 1/2 thicker, this would cut down on vibration, look better and make running the wires through the bars easier. August 21, 2016
Rated 4 out of 5 by Right fit for me I'm 6'4" and it was the right fit for me. Dealer said I had to lose the heated hand grips due to cabling restrictions (hole size) through the handlebar. Reason for not scoring a 5 June 22, 2016
Rated 1 out of 5 by Nor for me or my 2010 st glide Puts my wrists in a very uncomfortable position, I will replace these bars first chance I get. April 5, 2016
Rated 4 out of 5 by Mini Apes on 2014 Limited These look great on my bike. Hands rest just at the top of the speakers. Not to much wind drag on my knuckles. Just a guess but hands are appox 4" below my shoulders sitting on a stock tour seat. Angle of the grips are a bit flatter than stock. I got use to the grip angle in about a hundred miles. Was able to reinstall stock heated grips. Dealer explained small tab inside the heated grip needed to be knocked down some. Or maybe they just used a bigger hammer. Either way they work. All wires and lines had to be extended. Everything except brake and clutch lines routed internally. After the break in period I find these bars to be very comfortable. I am 6' with average reach. 4 Stars simply because of the flat angle of the grips. But as I said I got use to them. June 24, 2015
  • 2016-09-22 T12:47:54.012-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_4, tr_4
  • loc_en_US, sid_PA-09-5748511, prod, sort_default
1-4 of 4
Ask your questions. Share your answers.
9 Questions | 8 Answers

Product Q&A

Ask your questions. Share your answers.

 
 
« Back
 
 
July 24, 2016
Customer avatar
by
Read all my Q&A
 
Please wait while more information about Robbins1 is loaded.
Additional information about Robbins1 could not be loaded.
Alexander arkansas
I Ride: Street glide and heritage classic
How I Ride: Local - With Passenger
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Robbins1,

When changing handlebars it is recommended cables and wires be replaced as well. The same goes for the Batwing Mini-Ape Handlebar--cables and wires must be changed.

Thanks!
July 26, 2016
Customer avatar
by
Read all my Q&A
 
Please wait while more information about RowdyGrl79 is loaded.
Additional information about RowdyGrl79 could not be loaded.
Milwaukee, WI, USA
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
 
1 answer

How wide are the bars tip to tip?

Looking to install on my 15 Road Glide Special. I don't want something too wide though. A lot that I am coming across are 37". I was looking for something that is more around 31" or 32" wide.
May 9, 2016
Customer avatar
by
Read all my Q&A
 
Please wait while more information about HarimauSilat is loaded.
Additional information about HarimauSilat could not be loaded.
Quincy, MA
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi HarimauSilat,

The tip to tip length of this Batwing Mini-Ape Handlebar is 35 inches.

Thank you for your question.
May 11, 2016
Customer avatar
by
Read all my Q&A
 
Please wait while more information about FXS78 is loaded.
Additional information about FXS78 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
December 26, 2015
Customer avatar
by
Read all my Q&A
 
Please wait while more information about rusburnett is loaded.
Additional information about rusburnett could not be loaded.
Corinth MS
I Ride: 2009 FLHX
How I Ride: Local - With Passenger
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Rusburnett,

Yes, this Batwing Mini-Ape Handlebar does require the separate purchase of additional components for installation. Please refer to the "Bat Wing Mini-Ape Handlebar" link, under the "More Info" tab for assistance.

Thank you for your question.
February 25, 2016
Customer avatar
by
Read all my Q&A
 
Please wait while more information about FXS78 is loaded.
Additional information about FXS78 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
What options do I have without adding cables and wires. 10 "
October 17, 2015
Customer avatar
by
Read all my Q&A
 
Please wait while more information about JACKDANIELS is loaded.
Additional information about JACKDANIELS could not be loaded.
Canada
I Ride: 2009 Electra Glide Standard
How I Ride: Touring - Solo
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hello JACKDANIELS, this handlebar does not come in 10".

The additional parts you will need to make this work will be,
Socket housing, two-way; Secondary lock, two-way socket housing; Seal pin (plug) (2); Pin housing, two-way; Secondary lock, two-way pin housing.

Thank you for your question.
October 19, 2015
Customer avatar
by
Read all my Q&A
 
Please wait while more information about Iceman25 is loaded.
Additional information about Iceman25 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
March 5, 2015
Customer avatar
by
Read all my Q&A
 
Please wait while more information about JBHOGG is loaded.
Additional information about JBHOGG could not be loaded.
Dayton,Ohio
I Ride: 2013 Street Glide
How I Ride: Local - With Passenger
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hello Jbhogg,

These handlebars will not work with your stock cables and brake lines. Please see the attachment below for the part numbers you will need.

http://www.harley-davidson.com/app-...

Thank you!
March 16, 2015
Customer avatar
by
Read all my Q&A
 
Please wait while more information about JD34 is loaded.
Additional information about JD34 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
  • 2016-09-22 T12:47:05.894-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_PA-09-5748511, prod, sort_default
2 next>>
  • 2016-09-22 T12:47:05.909-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_PA-09-5748511, prod, sort_default
2 next>>
Ride Free. Ship Free. Return Free.

FREE SHIPPING AND RETURNS TO YOUR LOCAL DEALER. DETAILS

You Might Also Like

Recently Viewed


    Prices listed are generally the Manufacturer's Suggested Retail Price (MSRP), excluding taxes and shipping. Prices at local dealerships may vary. All online orders will be fulfilled and shipped by
    Harley-Davidson Motor Company as the agent for the Selling Dealer.